Current Status of WB6NDJ EchoIRLP Node.

Current Map of WB6NDJ EchoIRLP Connection (if any).  This map is interactive and zoomable.

WB6NDJ EchoIRLP Node

IRLP 3115 Echolink 270352

Repeater 442.40+ PL 77.0

EchoIRLP is a developing project with a goal to share hardware and software resources for IRLP and EchoLink systems. Software is installed and being tested that allows the WB6NDJ IRLP node Linux computer system to connect to EchoLink network nodes and IRLP network nodes.

For more information on each system please visit the following websites:
www.irlp.net
www.echolink.org

The software installed on the WB6NDJ IRLP node is referred to as the "EchoIRLP" project.

What this software does or does not do:

• Does not allow you to cross connect the IRLP and EchoLink networks together.

• Does provide the WB6NDJ IRLP node access to available EchoLink clients and conferences.

• Does allow EchoLink clients to connect to the WB6NDJ-R EchoLink node number 270352.

The following DTMF code list controls the operation of the WB6NDJ EchoIRLP node. General EchoIRLP node numbers would be prefixed with dtmf “D”. This insures EchoIRLP dtmf codes to bypass the controller.

General Controls:

DTMF Code Description

DA0 - Announce node status, e.g. link clear, connected, etc.

DA1 - Announce local node date and time.

DA33 - Announce local weather for Metro Oakland  International Airport.

DA34 - Announce weather alert for East Bay Oakland Hills.

DXXXX - Connect to IRLP node/reflector - four digit number.

D#XXXXX - Connect to Echolink node/conference number.

D73 - Disconnect from node, reflector or conference.

You can get the current Node, Reflector or Conference numbers from www.irlp.net or www.echolink.org .

GENERAL IRLP (ECHOLINK) USER GUIDELINES

As with any new technology, it does take some time to adapt to operating procedures that differ from conventional FM repeater use. This work in progress can serve as a guideline for those wishing to use their local IRLP enabled repeater node.

COMMON MODES

There are two connection modes for an IRLP connection. Direct one-to-one or, one-to-many via a Reflector. Direct connect is just like it sounds where repeater (node) "A" connects direct with node "B". With this type of link the two nodes are interconnected and no other IRLP connections are possible. While repeaters "A" and "B" are connected, anyone attempting to connect with either node will be told by a recording that - "The node you are calling is currently connected to callsign" however all local traffic on each repeater will be heard on the other repeater as well. While Direct Connect is preferred for a city-to-city chat, the most common type of connection in use today is via Reflector. A reflector is a Linux computer that is not connected to any radio but rather sits on lots of Internet bandwidth capable of allowing many repeaters to be inter-connected together by streaming the received audio back to all other connected stations. Each reflector has 9 sub channels allowing up to 10 separate virtual reflectors to operate. These are identified by the last digit. For example - 9250 is the main channel with 9251, 9252 9253 etc being virtual reflectors with identical capability as the main channel. You can always check which stations are connected to the reflectors main and sub-channels by visiting http://status.irlp.net and looking for nodes connected to individual nodes or reflectors.

REFLECTOR / CONFERENCE USE

With reflector use the first thing we must all remember is to leave a gap between transmissions. Having said that this is a good time to list the three main rules when connected to a reflector:

Pause

Pause

Pause

Due to the slight increase in delays created by multiple Tone Squelch radios in the links between the repeater and IRLP link radio, a slight change in our normal operating procedures is required with IRLP. By leaving a pause between transmissions it allows users on other nodes a chance to check in. Allows other nodes time to send touch-tone commands to drop their node. The most important guideline to remember is leaving a pause after pressing the PTT button as well as between transmissions.

Avoid local traffic while connected to the reflector. By its nature, the reflector has a large footprint and a wide audience, therefore if local users would like to have a discussion, they should disconnect from the reflector.

Along the same line, if two stations become engaged in an extended dialog involving only themselves, then I would recommend they both move off the reflector and make a direct node to node connection, freeing up the reflector for others. If more than two nodes are involved, then moving to one of the lesser-used reflectors might be an alternative, especially if one of the stations can check the web site for an available reflector. In the future, moving to one of the available sub-channels will become an option.

To make a contact, it is preferable to say "This is KB6XYZ is anyone available for a contact?" as opposed to "KB6XYZ Listening" ...silence for 2 minutes, followed by a disconnect. It IS acceptable to talk about the weather, or anything else that is geographically significant. But like anything else, within reason. A station in Indiana that says to a Colorado op, "Hey I heard that you have a mountain out there" will probably cause eyes to roll worldwide. In general though, long winded, channel-consuming conversations should be avoided. Remember there are usually a dozen or two connected systems, with perhaps hundreds of users that might like a chance to use the system.

A few other Reflector operational guidelines:

Listen first. When connecting to the main channel on a Reflector, odds are that you are dropping into an existing conversation.

Wait for at least 15 seconds to make sure you are not interrupting an existing QSO before calling.

Pause between transmissions. Many nodes are connected using simplex links, therefore the only time it is possible for them to disconnect is between transmissions. Be sure to pause AT LEAST 5 seconds between transmissions.

Key your transmitter and wait before speaking. There are propagation delays across the Internet, as well as delays caused by sub audible tone decoders and other devices that cause a delay before the audio path is cut through. If you speak immediately upon PTT, the beginning of your transmission will not be heard.

MAKING A DIRECT CONNECTION

First of all listen on your local machine for at least 15-30 seconds before transmitting and then ask if the repeater is currently in use. Assuming all is clear, identify your self and announce your intention to make an IRLP call. Example: "KB6XYZ connecting to IRLP node" then enter the code for the node and release your PTT. Your local repeater should come up with a carrier as it waits for the connection to be authenticated. This can take a few seconds of dead-air so don't be concerned. When the connection is confirmed, the voice ID of the destination node will be transmitted back to you as well as your nodes voice ID to the other repeater. NOTE: If your node is already connected to another node or reflector, a greeting will play saying - "your node is currently connected to...ID of the connection") In this case confirm if anyone desires the connection to remain up before dropping by using the disconnect code. Once connected and after hearing the confirming voice ID, wait at least 15 seconds before transmitting as the repeater may be in use, and your entry may have occurred between transmissions. The voice ID of your node is longer than the voice ID of their node, and the connection is not made until the ID is fully played. Their computer may be slower, and hence take longer to process the connection than yours. Press and hold the microphone PTT for a second and then announce your presence and your intention such as you are calling someone specifically or just looking for a QSO with another ham in that city. If no response is heard, announce your call and your intent to drop the link and then touch-tone in the disconnect code. Not a good idea to transmit touch-tone commands without first giving your callsign. Not only is this courteous it is a regulatory issue in some countries who may be connected to the reflector. Some nodes are configured so you cannot connect to them if that repeater is active. In this case you will receive the message "The node you are calling is being used locally" If you receive this message wait 5 or 10 minutes and then try again. If you stay connected to a node and there is no activity on your repeater for 4 minutes, the connection will time out and automatically disconnect with a voice ID disconnect message on both nodes.

CONNECTING TO THE REFLECTOR

As above, listen to your local machine for local use and then announce your intention for the Reflector before keying the connect command. When you hear the confirmation ID always WAIT at least 15 seconds before transmitting as you are most likely now connected with many repeaters and a QSO could be in progress. If after 15 seconds you hear nothing, identify yourself and indicate you are listening to the Reflector from "City and, State ". With the world wide IRLP activity your local repeater now has world wide coverage thus the suggestion to better detail your QTH. Don't be in a hurry to hear someone come back to you. You may have to do a bid of pleading from time-to-time to dislodge someone from whatever they are currently involved with. By default, if you stay connected to a reflector with and there is no activity on your repeater for 20 minutes, the connection will time out and automatically disconnect. However many node owners set this period for a long period so it is not unusual for repeaters with minimal traffic to stay connected to the Reflector for extended periods of time. When or if the node times out from a Reflector connection a standard time-out greeting will precede the timeout saying, "Activity time out ... Reflector xxxx, link off" If you hear or wish to engage in a prolonged rag-chew on your local repeater (long discussion of a local nature) out of courtesy to other node listeners drop the reflector.

ERROR MESSAGES

From time-to-time you may receive error messages when attempting to connect with a node or reflector. The most common ones are:

"The node you are calling is not responding, please try again later"
This is caused by a loss of Internet connectivity to one end of the call attempt.

"BEEP Error - The call attempt has timed out, the connection has been lost"
This error occurs when a node is OFF-LINE. Some nodes such as in the UK use dial-up connections and then, only for short periods. Also there may be temporary net or node problems.

"The Connection Has Been Lost"
If the Internet connection drops, this error message will be heard.

DO'S and DON'TS

In summary then a few do's and don'ts

DO pause between transmissions to let others in or others to enter DTMF command.

DO identify before sending DTMF command tones.

DO hold your microphone PTT for about 1 second before talking to allow all systems time to activate.

DO NOT rag-chew on your local repeater while connected to the reflector.

DO pause for 15 seconds or when entering the reflector before talking.

DO NOT start or plan a Net without pre-authorization from the reflector owner.